For ThrottleMax Calibration, exit at High Stick(Yellow LED)for Limiter mode and Low stick for governor mode(Green LED)
The target rotor speed can be calculated using
the ATV
Calculator
Example 1): 2 speed setup:
Gear ratio = 9.3:1
ATV- = 62%, ATV+ = 75%
GEAR Sw Posn
Rotor RPM
down (MIX)
1600
up (GEAR/INVERT) 1800
Example 2): 1 speed setup and disable:
Gear ratio = 9.3:1
ATV- = 0%, ATV+ = 75%
GEAR Sw Posn
Rotor RPM
down (MIX)
Disabled
up (GEAR/INVERT) 1800
Example 3): Flight Mode Mixing:
Set
the throttle curves in Flight modes 1 and 2 above the throttle priority level.
Set the GEAR switch to the (MIX) position
Set the GEAR ATV [TRVL ADJ] to -0%
Set the GEAR switch to the up (GEAR/INVERT)
position
Set the GEAR ATV [TRVL ADJ] to +100%
[PROG.Mix3] - This mix disables the Governor
in flight mode 'N'
GEAR->GEAR
RATE:->-100%
0%
SW: ON, Offset
0
[PROG.Mix2] - This mix sets the target rpm to
1600rpm (62%) in flight mode '1'
GEAR->GEAR
[Select Point-H]
Set the rate to 62
[Select Point-L]
Set the rate to 0
[Ignore Point-1, Point-2 and Point-3]
SW: F-S12
[PROG.Mix1] - This mix sets the target rpm to
1800 (75% - 62% see note below) in flight mode '2'
GEAR->GEAR
[Select Point-H]
Set the rate to 13 (see note below)
[Select Point-L]
Set the rate to 0
[Ignore Point-1, Point-2 and Point-3]
SW: F-2
Note: The Mix1 rate is 75 (1800rpm) - 62 (1600rpm) = 13%
GEAR Sw Posn
Flight Mode Rotor RPM
down (MIX)
N
Disabled
1
Disabled
2
Disabled
up (GEAR/INVERT)
N
Disabled
1
1500 rpm
2
1800rpm
OPTION 2, AUX3 channel sets RPM
The throttle connects to THRO channel (1)
The auxiliary connects to AUX3 channel (8)
ATV setup [TRVL ADJ]
Setup the throttle with as much ATV range as
possible.
AUX3 is already mixed to the flight mode
switch. The ATV in normal flight mode is +100, in flight mode1 the ATV
is 0 and in Flight mode 2 the ATV is -100.
Set the AUX3 ATV [TRVL ADJ] to +100% in N and
Flight S1 and S2 switch positions.
Remove any V curves or idle up curves (they can be restored after
calibration) on the throttle in S1 and S2 flight modes and put in the default curves: 0,25,50,75,100.
Inhibit any mixing on AUX 3. Toggle the flight mode switch (n - 1 -
2- 1 - n) to enter
and leave calibration.
Two mixes are used to add offsets to AUX 3
in each flight mode so that, in this example, Normal mode disables the
Governor, flight mode 1 sets 1500rpm and flight mode 2 sets 1800rpm.
Hint: You can observe the AUX3 range on the [MONIT]
screen
[PROG.Mix1] - This mix flattens the AUX3 channel to disable the TJ in
each flight mode switch position.
AUX3->AUX3
Point-L:-> 100
Point-1:-> INH
Point-2:-> 0
Point-3:-> INH
Point-H:-> -100
SW: ON
[PROG.Mix2] - This mix sets the target rpm to
1600rpm (62%) in flight mode '1' and 1800rpm (75%) in flight mode 2.
